rev. 0 information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of analog devices. a low voltage, resistor programmable thermostatic switch ad22105 ? analog devices, inc., 1996 one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 617/329-4700 fax: 617/326-8703 features user-programmable temperature setpoint 2.0 8 c setpoint accuracy 4.0 8 c preset hysteresis wide supply range (+2.7 v dc to +7.0 v dc) wide temperature range (C40 8 c to +150 8 c) low power dissipation (230 m w @ 3.3 v) applications industrial process control thermal control systems cpu monitoring (i.e., pentium) computer thermal management circuits fan control handheld/portable electronic equipment the ad22105 is designed to operate on a single power supply voltage from +2.7 v to +7.0 v facilitating operation in battery powered applications as well as in industrial control systems. because of low power dissipation (230 m w @ 3.3 v), self- heating errors are minimized and battery life is maximized. an optional int ernal 200 k w pull-up resistor is included to facilitate driving light loads such as cmos inputs. alternatively, a low power led indicator may be driven directly. general description the ad22105 is a solid state thermostatic switch. requiring only one external programming resistor, the ad22105 can be set to switch accurately at any temperature in the wide operating range of C40 c to +150 c. using a novel circuit architecture, the ad22105 asserts an open collector output when the ambient tempe rature exceeds the user-programmed setpoint temperature. the ad22105 has approximately 4 c of hysteresis which prevents rapid thermal on/off cycling. functional block diagram 1 2 3 4 8 7 6 5 nc v s r set nc r pull?p out gnd nc temperature sensor 200k w set point ad22105 12 3 4 8 7 65 out +2.7v to +7.0v r set ad22105 top view figure 1. typical application circuit
ad22105Cspecifications parameter symbol conditions min typ max units temperature accuracy ambient setpoint accuracy acc 0.5 2.0 c temperature setpoint accuracy acc t C40 c t a +125 c 3.0 c power supply rejection psr +2.7 v 1 < v s < +7.0 v 0.05 0.15 c/v hysteresis hysteresis value hys 4.1 c open collector output output low voltage v ol i sink = 5 ma 250 400 mv power supply supply range v s +2.7 +7.0 v supply current, output low is on 120 m a supply current, output high is off 90 m a internal pull-up resistor r pull-up 140 200 260 k w turn-on settling time t on 5 m s notes 1 the ad22105 will operate at voltages as low as +2.2 v. specifications subject to change without notice. rev. 0 C2C (v s = 3.3 v, t a = +25 8 c, r load = internal 200 k v , unless otherwise noted) set point temperature ? c 80 0 70 40 30 20 10 60 50 5 15 25 35 45 55 65 75 ?0 150 ?5 r set - k w 0 25 50 75 100 125 r set = ??90.3k w 39m w c t set ( c) + 281.6 c figure 2. setpoint resistor values
ad22105 rev. 0 C3C absolute maximum ratings* maximum supply voltage . . . . . . . . . . . . . . . . . . . . . . . +11 v maximum output voltage (pin 2) . . . . . . . . . . . . . . . . +11 v maximum output current (pin 2) . . . . . . . . . . . . . . . 10 ma operating temperature range . . . . . . . . . . C50 c to +150 c dice junction temperature . . . . . . . . . . . . . . . . . . . . +160 c storage temperature range . . . . . . . . . . . . C65 c to +160 c lead temperature (soldering, 10 sec) . . . . . . . . . . . +300 c *stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. ordering guide package package model description option ad22105ar 8-lead soic so-8 AD22105AR-REEL7 8-lead soic so-8 pin configuration 1 2 3 4 8 7 6 5 nc = no connect ad22105 r pull-up nc r set v s nc out gnd nc top view (not to scale) pin description pin no. description 1r pull-up, internal 200 k w (optional) 2 out 3 gnd 4 no connection 5 no connection 6r set , temperature setpoint resistor 7v s 8 no connection warning! esd sensitive device caution esd (electrostatic discharge) sensitive device. electrostatic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge without detection. although the ad22105 features proprietary esd protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality.
ad22105Ctypical performance characteristics rev. 0 C4C error ? c temperature ? c 4 ? ?0 150 ?5 0 25 50 75 100 125 3 0 ? ? ? 2 1 guaranteed limit (+) guaranteed limit (? figure 3. error vs. setpoint error ? c/% temperature ? c 0.1 0.3 1.1 ?0 150 ?5 0 25 50 75 100 125 0.5 0.7 0.9 figure 4. setpoint error due to r set tolerance i s ?? temperature ? c 90 40 ?0 150 ?5 0 25 50 75 100 125 80 60 50 70 v s = 7v v s = 5v v s = 3v figure 5. supply current vs. temperature (v out = high) hysteresis ? c temperature ? c 4.4 3.2 ?0 150 ?5 0 25 50 75 100 125 4.2 4.0 3.8 3.6 3.4 figure 6. hysteresis vs. setpoint error ? c v s 2.0 1.5 ?.0 37 45 6 0.0 ?.5 ?.0 ?.5 1.0 0.5 +125 c +25 c ?0 c figure 7. setpoint error vs. supply voltage i s ?? temperature ? c 120 60 ?0 150 ?5 0 25 50 75 100 125 110 100 90 80 70 v s = 7v v s = 5v v s = 3v figure 8. supply current vs. temperature (v out = low)
ad22105 rev. 0 C5C 0.4 0.3 0.0 10? 10ma 1ma 100? 1? 0.2 0.1 i out v out t a = +150 c t a = +25 c t a = ?0 c figure 9. v out vs. i out (v out = low) t ?sec flow rate ?cfm 16 14 2 0 1200 400 800 10 8 6 4 12 figure 10. thermal response vs. flow rate flow rate ?cfm 250 200 0 1200 q ja ? c/w 400 800 150 100 50 figure 11. thermal resistance vs. flow rate % of final value time ?sec 100 80 0 060 10 20 30 40 50 60 40 20 90 70 50 30 10 still air moving air (1200 cfm) figure 12. thermal response time
ad22105 rev. 0 C6C product description the ad22105 is a single supply semiconductor thermostat switch that utilizes a unique circuit architecture to realize the combined functions of a temperature sensor, setpoint comparator, and output stage all in one integrated circuit. by using one external resistor, the ad22105 can be programmed to switch at any temperature selected by the system designer in the range of C40 c to +150 c. the internal comparator is designed to switch very accurately as the ambient temperature rises past the setpoint temperature. when the ambient temperature falls, the comparator relaxes its output at a somewhat lower temperature than that at which it originally switched. the difference between the switch and unswitch temperatures, known as the hysteresis, is designed to be nominally 4 c. the setpoint resistor the setpoint resistor is determined by the equation: r set = 39 m w c t set ( c ) + 281.6 c 90.3 k w eq. 1 the setpoint resistor should be connected directly between the r set pin (pin 6) and the gnd pin (pin 3). if a ground plane is used, the resistor may be connected directly to this plane at the closest available point. the setpoint resistor, r set , can be of nearly any resistor type, but its initial tolerance and thermal drift will affect the accuracy of the programmed switching temperature. for most applications, a 1% metal-film resistor will provide the best tradeoff between cost and accuracy. calculations for computing an error budget can be found in the section effect of resistor tolerance and thermal drift on setpoint accuracy. once r set has been calculated, it may be found that the calcu- lated value does not agree with readily available standard resistors of the chosen tolerance. in order to achieve an r set value as close as possible to the calculated value, a compound resistor can be constructed by connecting two resistors in series or in parallel. to conserve cost, one moderately precise resistor and one lower precision resistor can be combined. if the mod- erately precise resistor provides most of the necessary resistance, the lower precision resistor can provide a fine adjustment. con- sider an example where the closest standard 1% resistor has only 90% of the value required for r set . if a 5% series resistor is used for the remainder, then its tolerance only adds 5% of 10% or 0.5% additional error to the combination. likewise, the 1% resistor only contributes 90% of 1% or 0.9% error to the combi- nation. these two contributions are additive resulting in a total compound resistor tolerance of 1.4%. effect of resistor tolerance and thermal drift on setpoint accuracy figure 3 shows the typical accuracy error in setpoint temperature as a function of the programmed setpoint temperature. this curve assumes an ideal resistor for r set . the graph of figure 4 may be used to calculate additional setpoint error as a function of resistor tolerance. note that this curve shows additional error beyond the initial accuracy error of the part and should be added to the value found in the specifications table. for example, consider using the ad22105 programmed to switch at +125 c. figure 4 indicates that at +125 c, the additional error is approximately C0.2 c/% of r set . if a 1% resistor (of exactly correct nominal value) is chosen, then the additional error could be C0.2 c/% 1% or C0.2 c. if the closest standard resistor value is 0.6% away from the calculated value, then the total error would be 0.6% for the nominal value and 1% for the tolerance or (1.006) (1.10) or 1.01606 (about 1.6%). this could lead to an additional setpoint error as high as 0.32 c. for additional accuracy considerations, the thermal drift of the setpoint resistor can be taken into account. for example, con- sider that the drift of the metal film resistor is 100 ppm/ c. since this drift is usually referred to +25 c, the setpoint resistor can be in error by an additional 100 ppm/ c (125 c C 25 c) or 1%. using a setpoint temperature of 125 c as discussed above, this error source would add an additional C0.2 c (for positive drift) making the overall setpoint error potentially C0.52 c higher than the original accuracy error. initial tolerance and thermal drift effects of the setpoint resistor can be combined and calculated by using the following equation: r max = r nom (1 +e ) 1 + t c ( t set 25 c ) () where: r max is the worst case value that the setpoint resistor can be at t set , r nom is the standard resistor with a value closest to the desired r set , e is the 25 c tolerance of the chosen resistor (usually 1%, 5%, or 10%), t c is the temperature coefficient of the available resistor, t set is the desired setpoint temperature. once calculated, r max may be compared to the desired r set from equation 1. continuing the example from above, the required value of r set at a t set of 125 c is 5.566 k w . if the nearest standard resistor value is 5.600 k w , then its worst case maximum value at 125 c could be 5.713 k w . again this is +2.6% higher than r set leading to a total additional error of C0.52 c beyond that given by the specifications table. the hysteresis and self-heating the actual value of the hysteresis generally has a minor dependence on the programmed setpoint temperature as shown in figure 6. furthermore, the hysteresis can be affected by self- heating if the device is driving a heavy load. for example, if the device is driving a load of 5 ma at an output voltage (given by figure 9) of 250 mv, then the additional power dissipation would be approximately 1.25 mw. with a q ja of 190 c/w in free air the internal die temperature could be 0.24 c higher than ambient leading to an increase of 0.24 c in hysteresis. in the presence of a heat sink or turbulent environment, the additional hysteresis will be less.
ad22105 rev. 0 C7C output section the output of the ad22105 is the collector of an npn transistor. when the ambient temperature of the device exceeds the programmed setpoint temperature, this transistor is activated causing its collector to become a low impedance. a pull-up resistor, such as the internal 200 k w provided, is needed to observe a change in the output voltage. for versatility, the optional pull-up resistor has not been permanently connected to the output pin. instead, this resistor is undedicated and connects from pin 7 (v s ) to pin 1 (r pull-up ). in order to use r pull-up a single connection should be made from pin 1 (r pull-up ) to pin 2 (out). the 200 k w pull-up resistor can drive cmos loads since essentially no static current is required at these inputs. when driving ls and other bipolar family logic inputs a parallel resistor may be necessary to supply the 20 m aC50 m a i ih (high level input current) specified for such devices. to determine the current required, the appropriate manufacturers data sheet should be consulted. when the output is switched, indicating an over temperature condition, the output is capable of pulling down with 10 ma at a voltage of about 375 mv. this allows for a fan out of 2 with standard bipolar logic and 20 with ls family logic. low power indicator leds (up to 10 ma) can be driven directly from the output pin of the ad22105. in most cases a small series resistor (usually of several hundred ohms) will be required to limit the current to the led and the output transistor of the ad22105. mounting considerations if the ad22105 is thermally attached and properly protected, it can be used in any measuring situation where the maximum range of temperatures encountered is between C40 c and +150 c. because plastic ic packaging technology is employed, excessive mechanical stress must be avoided when fastening the device with a clamp or screw-on heat tab. thermally conductive epoxy or glue is recommended for typical mounting conditions. in wet or corrosive environments, an electrically isolated metal or ceramic well should be used to protect the ad22105. thermal environment effects the thermal environment in which the ad22105 is used determines two performance traits: the effect of self-heating on accuracy and the response time of the sensor to rapid changes in temperature. in the first case, a rise in the ic junction tempera- ture above the ambient temperature is a function of two variables: the power consumption of the ad22105 and the thermal resistance between the chip and the ambient environment, q ja . self-heating error can be derived by multiplying the power dissipation by q ja. because errors of this type can vary widely for surroundings with different heat sinking capacities, it is necessary to specify q ja under several conditions. table i shows how the magnitude of self-heating error varies relative to the environment. a typical part will dissipate about 230 m w at room temperature with a 3.3 v supply and negligible output loading. in still air, without a heat sink, table i indicates a q ja of 190 c/w, which yields a temperature rise of 0.04 c. thermal rise of the die will be considerably less in an environ- ment of turbulent or constant moving air or if the device is in direct physical contact with a solid (or liquid) body. response of the ad22105 internal die temperature to abrupt changes in ambient temperatures can be modeled by a single time constant exponential function. figure 11 shows typical response plots for moving and still air. the time constant, t (time to reach 63.2% of the final value), is dependent on q ja and the thermal capacities of the chip and the package. table i lists the effective t for moving and still air. copper printed circuit board connections were neglected in the analysis; however, they will sink or conduct heat directly through the ad22105s solder plated copper leads. when faster response is required, a therm- ally conductive grease or glue between the ad22105 and the surface temperature being measured should be used. table i. thermal resistance (so-8) medium u ja ( 8 c/watt) t (sec)* moving air** 100 3.5 without heat sink still air 190 15 without heat sink notes * *the time constant is defined as the time to reach 63.2% of the final tempera- ture change. **1200 cfm. using the ad22105 as a cooling setpoint detector the ad22105 can be used to detect transitions from higher temperatures to lower temperatures by programming the setpoint temperature 4 c greater than the desired trip point temperature. the 4 c is necessary to compensate for the nominal hysteresis value designed into the device. a more precise value of the hysteresis can be obtained from figure 6. in this mode, the logic state of the output will indicate a high for under temperature conditions. the total device error will be slightly greater than the specification value due to uncertainty in hysteresis. application hints emi suppression noisy environments may couple electromagnetic energy into the r set node causing the ad22105 to falsely trip or untrip. noise sources, which typically come from fast rising edges, can be coupled into the device capacitively. furthermore, if the output signal is brought close the r set pin, energy can couple from the out pin to the r set pin potentially causing oscillation. stray capacitance can come from several places such as, ic sockets, multiconductor cables, and printed circuit board traces. in some cases, it can be corrected by constructing a faraday shield around the r set pin, for example, by using a shielded cable with the shield grounded. however, for best performance, cables should be avoided and the ad22105 should be soldered directly to a printed circuit board whenever possible. figure 13 shows a sample printed circuit board layout with low inter-pin capaci- tance and faraday shielding. if stray capacitance is unavoidable, and interference or oscillation occurs, a low impedance capaci- tor should be connected from the r set pin to the gnd pin. this capacitor must be considerably larger than the estimated stray capacitance. typically several hundred picofarads will cor- rect the problem.
ad22105 rev. 0 C8C leakage at the r set pin leakage currents at the r set pin, such as those generated from a moist environment or printed circuit board contamination, can have an adverse effect on the programmed setpoint temperature of the ad22105. depending on its source, leakage current can flow into or out of the r set pin. consequently, the actual setpoint temperature could be higher or lower than the intended setpoint temperature by about 1 c for each 75 na of leakage. with a 5 v power supply, an isolation resistance of 100 m w would create 50 na of leakage current giving a setpoint temperature error of about 0.7 c (the r set pin is near ground potential). a guard ring can be placed around the r set node to protect against leakage from the power supply pin (as shown in figure 13). c1 pin 1 out gnd v s r set figure 13. suggested pcb layout c2099C6C1/96 printed in u.s.a. outline dimensions dimensions shown in inches and (mm). 8-lead soic (so-8) 0.1968 (5.00) 0.1890 (4.80) 8 5 4 1 0.2440 (6.20) 0.2284 (5.80) pin 1 0.1574 (4.00) 0.1497 (3.80) 0.0688 (1.75) 0.0532 (1.35) seating plane 0.0098 (0.25) 0.0040 (0.10) 0.0192 (0.49) 0.0138 (0.35) 0.0500 (1.27) bsc 0.0098 (0.25) 0.0075 (0.19) 0.0500 (1.27) 0.0160 (0.41) 8 0 0.0196 (0.50) 0.0099 (0.25) x 45
|
